围压条件下脉冲射流提高清岩效果数值模拟研究

刘爽; 李根生; 史怀忠

doi:10.13639/j.odpt.2015.03.002

高级检索

E-mail Alert

围压条件下脉冲射流提高清岩效果数值模拟研究

刘爽, 李根生, 史怀忠

文章导航 > 石油钻采工艺 > 2015 > 37(3): 6-10

刘爽, 李根生, 史怀忠. 围压条件下脉冲射流提高清岩效果数值模拟研究[J]. 石油钻采工艺, 2015, 37(3): 6-10. doi: 10.13639/j.odpt.2015.03.002

引用本文:

刘爽, 李根生, 史怀忠. 围压条件下脉冲射流提高清岩效果数值模拟研究[J]. 石油钻采工艺, 2015, 37(3): 6-10. doi: 10.13639/j.odpt.2015.03.002

LIU Shuang, LI Gensheng, SHI Huaizhong. Numerical simulation research on improving cleaning cuttings effectiveness with pulsed jet under confining pressure[J]. Oil Drilling & Production Technology, 2015, 37(3): 6-10. doi: 10.13639/j.odpt.2015.03.002

Citation:

LIU Shuang, LI Gensheng, SHI Huaizhong. Numerical simulation research on improving cleaning cuttings effectiveness with pulsed jet under confining pressure[J]. Oil Drilling & Production Technology, 2015, 37(3): 6-10. doi: 10.13639/j.odpt.2015.03.002

围压条件下脉冲射流提高清岩效果数值模拟研究

doi: 10.13639/j.odpt.2015.03.002

1.
中国石油大学油气资源与探测国家重点实验室，北京　102249

详细信息

中图分类号: TE21

Numerical simulation research on improving cleaning cuttings effectiveness with pulsed jet under confining pressure

1.
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing 102249, China

摘要: 脉冲射流钻井技术具有高效清岩能力，但其提速机制还不十分清楚。通过建立围压条件下单喷嘴脉冲射流井底清岩物理模型，对脉冲射流清岩过程进行了数值模拟研究，分析了影响脉冲射流清岩效果的主要因素。结果表明，非稳态旋流是脉冲射流提高清岩效果的主要原因之一，在相同排量条件下，脉冲射流清岩效率比连续射流平均提高约1~1.6 倍。脉冲射流清岩效率随着喷嘴直径和入口流速的增大而增大；围压对脉冲射流清岩过程影响较小；低频率脉冲射流的清岩总体效果较好；随着岩屑粒径增大，井底冲击区域内岩屑分布非均匀性增强，脉冲射流清岩效率降低。研究结果对指导脉冲射流提速技术的工程实践具有一定的参考价值。
- 钻井 /
- 脉冲射流 /
- 清岩 /
- 岩屑 /
- 数值模拟
Abstract: The drilling technology with pulsed jet is highly capable of cleaning the cuttings, but its acceleration mechanism remains unknown. By establishing a physical model for bottom hole cleaning cuttings by pulsed jet with single-nozzle under confining pressure, the numerical simulation research was conducted on the whole process of cleaning cuttings by pulsed jet, and the main factors affecting the cleaning cuttings effect by pulsed jet was analyzed. The research finding shows that unsteady state rotational flow is one of the main reasons for improvement of cleaning cuttings effect by pulsed jet. Under the same flow rate, the cleaning cuttings efficiency by pulsed jet is about 1-1.6 times that of continuous jet in average. The efficiency of cleaning cuttings by pulsed jet increases with the increase of nozzle diameter and inlet flowrate. The confining pressure has small effect on the process of cleaning cuttings by pulsed jet. The overall effect of cleaning cuttings by low frequency pulsed jet is good, with the increase of particle sizes, the heterogeneity of cuttings distribution within the impact area at hole bottom is intensified and the efficiency of cleaning cuttings by pulsed jet is reduced. The resulting conclusions provide a theoretical guidance for research on acceleration technique by pulsed jet.
- drilling /
- pulsed jet /
- cleaning cuttings /
- cuttings /
- numerical simulation

[1]	戴文潮. 预置管酸液射流钻进数值模拟与实验 . 石油钻采工艺, 2023, 44(): 1-7.
[2]	陈绪跃, 曹通, 高德利, 杨进, 刘明涛, 杨书港. 射流磨钻头流场特性及其外排屑槽影响的数值模拟 . 石油钻采工艺, 2020, 42(2): 162-166. doi: 10.13639/j.odpt.2020.02.007
[3]	甘泉泉, 刘少胡, 管锋, 李明红. 水平井段工具内脉冲射流冲砂技术 . 石油钻采工艺, 2019, 41(4): 549-554. doi: 10.13639/j.odpt.2019.04.023
[4]	王嘉松, 蒋世全, 许亮斌. 深水钻井隔水管涡激振动特性的数值模拟研究 . 石油钻采工艺, 2015, 37(1): 30-35. doi: 10.13639/j.odpt.2015.01.007
[5]	刘爽, 李根生, 史怀忠, 田守嶒. 水力脉冲射流旋流流场数值模拟 . 石油钻采工艺, 2015, 37(5): 17-21. doi: 10.13639/j.odpt.2015.05.005
[6]	康毅力, 皇凡生, 游利军, 俞杨烽, 练章华. 钻井液浸泡页岩裂缝宽度的模拟及应用 . 石油钻采工艺, 2014, 36(5): 41-46. doi: 10.13639/j.odpt.2014.04.011
[7]	欧阳勇, 周文军, 徐自强, 黄占盈. 频率可调式脉冲钻井提速工具的研制和应用 . 石油钻采工艺, 2013, 35(2): 6-8.
[8]	朱忠喜, 柳贡慧, 岳达明, 蒋记伟. 气体钻井岩屑运移破碎研究 . 石油钻采工艺, 2012, 34(1): 19-22.
[9]	肖国益, 赵向阳, 孟英峰, 朱化蜀, 练章华, 李皋. 气体钻井携岩关键点多相流动规律研究 . 石油钻采工艺, 2011, 33(1): 16-18.
[10]	林铁军, 练章华, 陈世春, 李敏, 陈峰. 气体钻井中气体携岩对钻杆的冲蚀机理研究 . 石油钻采工艺, 2010, 32(4): 1-4.
[11]	吕晓平, 安朝明, 胡水艳, 杨进. 自激谐振脉冲射流在玉门鸭945井的应用 . 石油钻采工艺, 2009, 31(4): 45-47.
[12]	倪红坚, 杜玉昆, 王瑞和. 井底岩屑磨料脉冲射流室内实验研究 . 石油钻采工艺, 2008, 30(5): 25-28.
[13]	王炳印, 卢晓峰, 曲从峰, 邓金根, 邹灵战. 疏松砂岩储层水平井安全钻井周期数值模拟计算 . 石油钻采工艺, 2005, 27(3): 11-12. doi: 10.3969/j.issn.1000-7393.2005.03.004
[14]	汪志明, 张政. 大斜度井两层稳定模型岩屑传输规律研究 . 石油钻采工艺, 2003, 25(4): 8-11. doi: 10.3969/j.issn.1000-7393.2003.04.003
[15]	谢翠丽, 杨爱玲, 陈康民. 旋转钻头射流方式对井底流场影响的数值剖析 . 石油钻采工艺, 2002, 24(3): 1-4. doi: 10.3969/j.issn.1000-7393.2002.03.001
[16]	李明川, 崔桂香. 变质量气液分层流动数值模拟 . 石油钻采工艺, 2001, 23(1): 47-50,84. doi: 10.3969/j.issn.1000-7393.2001.01.014
[17]	王富华, 邱正松, 鄢捷年, 王书琪, 朱金智. 钻井液添加剂定量荧光评价方法的探讨 . 石油钻采工艺, 2001, 23(3): 1-4,83. doi: 10.3969/j.issn.1000-7393.2001.03.001
[18]	张景富, 俞庆森, 严世才. 侧钻井钻井液携屑能力试验研究 . 石油钻采工艺, 2000, 22(2): 12-16. doi: 10.3969/j.issn.1000-7393.2000.02.003
[19]	汪海阁, 刘希圣, 丁岗. 水平井段偏心环空中岩屑运移机理的研究 . 石油钻采工艺, 1993, 15(6): 8-17,34. doi: 10.3969/j.issn.1000-7393.1993.06.002
[20]	刘永建, 孙维林. 球形岩屑在赫-巴流体中的沉降速度 . 石油钻采工艺, 1990, 12(3): 15-18,44. doi: 10.3969/j.issn.1000-7393.1990.03.003

点击查看大图

计量

文章访问数: 433
HTML全文浏览量: 24
PDF下载量: 527
被引次数: 0

围压条件下脉冲射流提高清岩效果数值模拟研究

doi: 10.13639/j.odpt.2015.03.002

1. 中国石油大学油气资源与探测国家重点实验室，北京　102249

收稿日期: 2019-05-14
修回日期: 2019-05-14
刊出日期: 2015-06-23

中图分类号: TE21

关键词:

钻井 /

脉冲射流 /

清岩 /

岩屑 /

数值模拟

摘要: 脉冲射流钻井技术具有高效清岩能力，但其提速机制还不十分清楚。通过建立围压条件下单喷嘴脉冲射流井底清岩物理模型，对脉冲射流清岩过程进行了数值模拟研究，分析了影响脉冲射流清岩效果的主要因素。结果表明，非稳态旋流是脉冲射流提高清岩效果的主要原因之一，在相同排量条件下，脉冲射流清岩效率比连续射流平均提高约1~1.6 倍。脉冲射流清岩效率随着喷嘴直径和入口流速的增大而增大；围压对脉冲射流清岩过程影响较小；低频率脉冲射流的清岩总体效果较好；随着岩屑粒径增大，井底冲击区域内岩屑分布非均匀性增强，脉冲射流清岩效率降低。研究结果对指导脉冲射流提速技术的工程实践具有一定的参考价值。

English Abstract

Numerical simulation research on improving cleaning cuttings effectiveness with pulsed jet under confining pressure

1. State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing 102249, China

Received Date: 2019-05-14
Rev Recd Date: 2019-05-14
Publish Date: 2015-06-23

Keywords:

Abstract: The drilling technology with pulsed jet is highly capable of cleaning the cuttings, but its acceleration mechanism remains unknown. By establishing a physical model for bottom hole cleaning cuttings by pulsed jet with single-nozzle under confining pressure, the numerical simulation research was conducted on the whole process of cleaning cuttings by pulsed jet, and the main factors affecting the cleaning cuttings effect by pulsed jet was analyzed. The research finding shows that unsteady state rotational flow is one of the main reasons for improvement of cleaning cuttings effect by pulsed jet. Under the same flow rate, the cleaning cuttings efficiency by pulsed jet is about 1-1.6 times that of continuous jet in average. The efficiency of cleaning cuttings by pulsed jet increases with the increase of nozzle diameter and inlet flowrate. The confining pressure has small effect on the process of cleaning cuttings by pulsed jet. The overall effect of cleaning cuttings by low frequency pulsed jet is good, with the increase of particle sizes, the heterogeneity of cuttings distribution within the impact area at hole bottom is intensified and the efficiency of cleaning cuttings by pulsed jet is reduced. The resulting conclusions provide a theoretical guidance for research on acceleration technique by pulsed jet.

刘爽, 李根生, 史怀忠. 围压条件下脉冲射流提高清岩效果数值模拟研究[J]. 石油钻采工艺, 2015, 37(3): 6-10. doi: 10.13639/j.odpt.2015.03.002

引用本文:

刘爽, 李根生, 史怀忠. 围压条件下脉冲射流提高清岩效果数值模拟研究[J]. 石油钻采工艺, 2015, 37(3): 6-10. doi: 10.13639/j.odpt.2015.03.002

Citation:

全文HTML

下载: 全尺寸图片幻灯片

返回文章

用微信扫码二维码

分享至好友和朋友圈

通信地址: 河北省任丘市华北油田采油工程研究院邮政编码: 062552

电话: 0317-2723370, 2724207传真: 0317-2724207Email: syzc@vip.163.com

本系统由北京仁和汇智信息技术有限公司设计开发技术支持: info@rhhz.net

围压条件下脉冲射流提高清岩效果数值模拟研究

doi: 10.13639/j.odpt.2015.03.002

Numerical simulation research on improving cleaning cuttings effectiveness with pulsed jet under confining pressure

计量

出版历程

围压条件下脉冲射流提高清岩效果数值模拟研究

doi: 10.13639/j.odpt.2015.03.002

1. 中国石油大学油气资源与探测国家重点实验室，北京 102249

English Abstract

Numerical simulation research on improving cleaning cuttings effectiveness with pulsed jet under confining pressure

1. State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing 102249, China

全文HTML

目录

1. 中国石油大学油气资源与探测国家重点实验室，北京　102249